INTRODUCING THE

MAX CLIMBER 4000TP/M MV

A 4,000 LB HOIST WITH A FULL 13-FOOT DECK

The Max Climber 4000TP/M MV joins the BETA MAX Hoists line: a 4,000 lb variable-frequency, dual-purpose hoist that lifts material at 80 fpm and carries crews at 40 fpm.

MC4000TPM MV ISO

INTRODUCING THE

MAX CLIMBER 4000TP/M MV

A 4,000 lb Hoist with a Full 13-Foot Deck

The Max Climber 4000TP/M MV joins the BETA MAX Hoists line: a 4,000 lb variable-frequency, dual-purpose hoist that lifts material at 80 fpm and carries crews at 40 fpm.

Share This Post

The Max Climber 4000TP/M MV gives crews the best of both worlds: the full 4,000 lb capacity and the full 13-foot deck in one machine. It is the first BETA MAX 4,000 lb configuration with the full 13-foot deck, offering 157.8″ × 59.3″ of internal loading area and nearly 65 sq ft of working surface. It lifts both material and crews, and a two-person crew can erect it.

MATERIAL HOIST AND TRANSPORT PLATFORM

The TP/M designation is the point of the machine: it runs as a material hoist or as a transport platform carrying crew and their tools. As a transport platform, it carries up to seven people, operator included, plus 2,800 lbs of material. As a material hoist, it carries the full 4,000 lbs with no riders. The 157.8″ × 59.3″ galvanized basket takes 12-foot sheets of drywall, pallets and mortar tubs, and the unique open/close unloading ramp system means the landing stays clear between lifts. 

MATERIAL HOIST
80 FPM

TRANSPORT PLATFORM
40 FPM

Variable frequency: a set speed for each mode

The MV in the model name stands for the variable-frequency drive. Each mode runs at its own set speed: 80 fpm in material hoist mode to keep the schedule moving, and 40 fpm in transport platform mode when people are on board. A mode selector on the onboard control panel switches between the two. Soft start and soft stop ramp the drive in and out of motion instead of snapping it, which protects finished stone and anything else that does not forgive a jolt. Operators feel it immediately: the basket arrives at the landing rather than lands on it.

Easier to put up, easier to live with

Lower pull-out and downward forces mean less structure to reinforce at the tie points. The fold-out platform lets a crew set wall ties from a safe, level surface, and the unit is self-erecting—build as you go, floor by floor, instead of staging the full mast up front. Each mast section stands 58.8″ tall and weighs 211 lbs, and a mast jib crane sets the sections in place. The ramps and wall ties mount on either side of the machine, so the hoist adapts to the building instead of the other way around. The footprint is roughly 98″ × 170″, which fits alleys, courtyards and the pinched setbacks that rule out bigger hoists. Electrical panels are reachable without disassembly, and the loading and lifting units are fully galvanized, so a winter on site does not turn into a spring refurbishment.

SMALL DETAILS THAT SAVE TIME

We work smart to make your life easier. The MC4000TP/M MV is full of features that operators notice on the first day:

  • Stop Next Floor. One press while the platform is moving tells it to stop at the next landing.
  • Self-relocking exit ramp. The exit ramp unlocks from the control panel and relocks automatically after 30 seconds if no one opens it.
  • Ground approach stop. In transport platform mode, the platform stops 10 ft above the ground before the operator completes the descent.
  • Automatic mast greaser. It lubricates the rack on every upward trip, so greasing does not stop the job.
  • Roof. A roof installs on the loading unit when the site assessment identifies a falling-object hazard.

BUILT TO BRING YOUR CREW HOME SAFE

Safety is built into every MC4000TP/M MV, with layered protection for the people riding it and the crew working around it:

  • Electromechanical safety brake (anti-fall device), drop-tested after every installation
  • Electrical and mechanical interlocks on the access doors, plus interlocks on the base enclosure door and the anchor-mounting platform
  • Load cells that monitor the payload and alert the operator to an overload
  • Manual brake release for emergency descent, and motor brakes that engage automatically if power is lost
  • Upward and downward overtravel, slowdown and stopping devices, with automatic floor-level stops
  • Fold-out platform for setting wall ties from a safe, level surface
  • Soft start and soft stop that keep loads and riders steady

SPECIFICATIONS

ModelMAX CLIMBER 4000TP/M MV
ConfigurationTransport platform / material, VFD
Lift capacityMaterial hoist mode: 4,000 lbs, no riders
Transport platform mode: 7 persons including operator, plus 2,800 lbs
Lift speed80 fpm in material hoist mode; 40 fpm in transport platform mode
Basket dimensions157.8" × 59.3" internal (approx. 65 sq ft working surface)
Mast section58.8" tall, 211 lbs
Max wind speed40 mph in operation; 28 mph during installation
A/C power208Vac, 3-phase, 80A required power line
Max lift height500 ft with anchored mast
Tie spacing22.96 ft maximum between wall anchors; first permanent anchor at 22.96 ft
Placement footprintApprox. 98" × 170"; 234.4" overall length with both ramps open
Transport height94" collapsed
Complete base unit weight4,405 lbs
StandardsANSI/ASSP A10.5, ANSI/SAIA A92.10

Information is intended to be informative only and does not constitute a representation or warranty. Prices and information are subject to change. Renderings may vary from the actual hoists.

DIMENSIONS

BASKET LENGTH

157.8″

BASKET WIDTH

59.3″

MACHINE LENGTH

168.1″

MACHINE WIDTH

91.5″

LENGTH WITH RAMP OPEN

234.4″

BASKET LENGTH

157.8″

BASKET WIDTH

59.3″

MACHINE LENGTH

168.1″

MACHINE WIDTH

91.5″

LENGTH WITH RAMP OPEN

234.4″

BASKET LENGTH

157.8″

BASKET WIDTH

59.3″

MACHINE LENGTH

168.1″

MACHINE WIDTH

91.5″

LENGTH WITH RAMP OPEN

234.4″

Plan-view dimensions in inches. The open ramps extend 31″ and 45.6″ beyond the basket, so allow for the full 234.4″ when planning the landing and ground-level loading area. The machine needs an approximate placement area of 98″ × 170″.

FREQUENTLY ASKED QUESTIONS

What power does the site need?

The MC4000TP/M MV requires a 208Vac, 3-phase, 80A power line. Share this with your electrician before installation.

In transport platform mode, up to seven people, operator included, plus 2,800 lbs of material. In material hoist mode, no riders are allowed except trained personnel during erection, dismantling and service.

Up to 500 ft with the mast anchored to the building. Wall anchors are spaced no more than 22.96 ft apart.

A two-person crew can erect the unit. It is self-erecting, so the mast goes up floor by floor as the building rises.

The hoist operates in winds up to 40 mph. Installation work stops above 28 mph.

Yes. The loading and lifting units are fully galvanized to resist corrosion through the season, and the hoist is rated to operate at temperatures down to 5°F.

Tell us where, how high, and when.
We will spec the hoist.

Prefer to talk it through? Call (800) 644-6478.

LIFT HIGHER WITH US

Stay up-to-date with the latest news and happenings at BETA MAX Hoists!

Please select all the ways you'd like to hear from us:

We use Mailchimp as our marketing platform. By clicking above to subscribe, you acknowledge that your information will be transferred to Mailchimp for processing. Learn more about Mailchimp’s privacy practices and Beta Max Inc.’s Privacy Policy.

You can unsubscribe at any time by clicking the link in the footer of our emails.

Related Posts

One Mast, Two Hoists

BETA MAX’s MC2000PMB V and MC2500TP/M MV run on a shared mast—cutting install time and spare-parts inventory for rental fleets.